Jack Up Floor Joists

The Saga of the Sagging Floor | See that cream-colored painted wood in between the two garage doors? Behind it is a wood column that’s rotting away causing the living-room floor above the garage to sag. Copyright 2020 Tim Carter

QUESTION: Howdy, Tim. Well, I really need your advice. I’m thinking of re-siding my house and it’s time to bite the bullet about repairing a structural issue that’s been getting worse each year. The floor in my living room has sagged two inches! The cause has been traced to a support column in between my two garage doors. I’m terrified as to what this might cost to repair and I have no idea what’s involved. Have you ever had to do a similar repair and who is best suited to correct the problem? What kind of column would you install so it never happens again? Stephen L., Worcester, MA

Why Do Floor Joists Sag?

Do you have a sagging floor like Stephen’s? They’re more common than you might think. In my opinion, the most common causes of sagging floors are wood-eating insects, wood rot caused by water leaks, undersized beams, and lastly soil settlement. There are other possible causes but in my experience the ones above account for much of the misery.

Jacking Up Joists - True Story

Years ago, a married couple hired me to build a room addition and complete a kitchen remodel job. They were so pleased with my work they then re-hired me to do lots of remodeling work on an existing home they moved to as their family grew. The house had a horrible sagging floor situation in the center of the house. An undersized beam in the basement was to blame and I fixed it by installing a new column in the basement.

I had to cut into the basement concrete floor to pour a new 3-foot by 3-foot by 1-foot-thick concrete footing pad. Once that was cured, I rented two house-lifting screw jacks. I installed cribbing on the new footer pad to support the jacks allowing myself space to install a new 4-inch steel column under the sagging beam once we had it re-leveled.

The trick is to lift the floor slowly. There was a staggering 3-inch dip in the floor so I decided to lift the floor 1/4 inch per day. It was easy to do and since I was in the house doing other work. I didn’t have to make all sorts of special trips back and forth to the house to adjust the jacks each morning.

In two weeks, the job was finished. Once the old beam was level again, I got the precise measurement I needed between the bottom of the beam and the top of the concrete pad. In one day my welder cut the steel pipe and welded on plates so I could bolt the column to the concrete footer and to the underside of the wood beam. I had the welder drill a hole near the top of the column so we could fill it with dry sand. This prevents the steel column from bending in the event of a house fire.

Should I Expose a Support Column?

The first step in Stephen’s journey is to expose the support column in between the two garage doors to see what might be the problem. Wood rot from water leakage or an insect issue should be straight forward. It’s important to realize if you see carpenter ants, they usually only like to live and tunnel in soft, moist wood so the issue is most likely a leak.

Settling soil can be a tougher problem to trace. If the support column is not rotted nor eaten by insects, then you need to start to look for other clues that might indicate the footing or foundation below the column has dropped. Check the garage floor for cracks around the support column and use a level to see if the floor is sloping to that area.

Should I Hire a Structural Engineer?

I feel the best money Stephen could spend on the job is to hire a residential structural engineer. CLICK or TAP HERE to get FREE BIDS from local structural engineers for your job. This professional has dealt with similar issues and can create a drawing that will communicate to bidding contractors exactly what needs to be done to fix the problem. Don’t allow a contractor to tell you he knows what to do unless he happens to also be a registered structural engineer.

Should I Use Steel Support Columns?

I’m very partial to using steel for support columns. It’s stronger than wood in almost all instances and it’s easy to have a local welder create exactly what the engineer might draw. Just about every engineer will allow the contractor to use solid-steel shims to make it easy to install custom-length steel columns.

How Do You Support Joists?

It’s very important that the engineer show in his drawings how to temporarily support the floor or the house as the repair work is being done. What’s more, be sure the engineer makes a recommendation to the amount of lift the contractor can do each day. You don’t ever want to try to jack up a beam in one hour that’s sagged 3 inches!

When Should I Get Bids From Contractors?

Once you’ve got the engineer’s plan, it’s time to start talking to remodeling contractors. These pros have the required skills. It’s vital you interview them and ask for at least three references where they have had to fix a similar structural issue. You want to call those homeowners to ask how everything turned out. You don’t want to be the contractor’s guinea pig for goodness sake!

Keep in mind steel columns come both round and square. Welders can do all sorts of things to make it easy for you to attach wood to the steel column should that be required. I always used the square columns on my jobs as I found them infinitely easier to work with.

Column 1375

The post Jack Up Floor Joists appeared first on Ask the Builder.